Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Morgan Hill Homeowners Choose CWS Construction
We’re an independent construction crew that provides CWS service in Morgan Hill, installing cabinetry and countertops throughout the area—from older orchard-era homes near the historic downtown to the 1990s and 2010s tract subdivisions and foothill custom homes east and west of the valley floor. No dealer affiliation, no manufacturer badge. Just years of hands-on familiarity with CWS box construction, hardware, and finish behavior. Our CWS work in Morgan Hill covers cabinet installation and refacing, quartz and granite countertops, and full kitchen design and layout, with the same crew managing every phase from tear-out to final walkthrough. Call (833) 725-3508 for a free estimate on your CWS project.
Why Trust Brookside Contractors for Your CWS Construction?
Nate Burrell, our owner and general contractor, grew up watching half the Paradise Valley neighborhoods get framed up when he was a kid, and he’s been on South Santa Clara County job sites for the better part of two decades since training in construction technology at Gavilan College. That background matters when you’re dealing with CWS cabinetry, because the difference between a kitchen that holds up and one that starts sagging at the drawer fronts usually comes down to whether the installer understood what the box needed before it ever left the shop. We know CWS ProSeries Shaker face frames, EuroStyle slab doors, Signature raised-panel profiles, and StoneCraft quartz the way a mechanic knows a particular engine. We’ve corrected enough soft-close glide failures, painted MDF joint cracks, and StoneCraft seam stress in Morgan Hill kitchens to diagnose most CWS problems over the phone before we ever set foot in the house.
As an independent CWS service provider, we’re not tied to a dealer quota or a manufacturer’s parts program. That means when a CWS cabinet run fails, we recommend what actually fixes it, not what’s easiest to bill. We use OEM CWS hinges, glides, and touch-up finishes when available, and we match premium aftermarket soft-close mechanisms to the existing box drilling when OEM parts are discontinued or slow to arrive. The goal is always the same: keep your CWS kitchen functional without voiding its warranty or charging for work you don’t need. Nate’s rule on the job site is simple. Do it once, do it right – everything else is just a future repair bill.
Styles & brands we work with
Common CWS Construction Problems We Fix in Morgan Hill
These are the failures we see repeatedly on CWS cabinetry and countertops in CWS in Seven Trees and throughout Morgan Hill homes. If you’re dealing with one of these, you’re not alone, and most are repairable without tearing out the whole kitchen.
- Soft-close drawer glides losing dampening or sagging on CWS ProSeries Shaker boxes. Wide pot drawers take a beating, and after years of daily use the dampener piston on the glide wears out, so the drawer slams instead of gliding. The front rail on wide drawers also sags when the box wasn’t reinforced at install, causing the drawer face to rub the adjacent door. We replace the glides with OEM-matched soft-close units and re-square the face frames so the reveals are even again.
- Hairline cracks at stile-and-rail joints on painted CWS EuroStyle and Shaker doors. Morgan Hill’s hot, dry inland summers pull moisture out of MDF, and winter swings push it back in. That expansion and contraction eventually opens hairline cracks at the joints and around hinge mounts on painted doors and face frames. We refinish or replace the affected doors, then re-seal the joints so the cycle doesn’t repeat as quickly.
- Chipping and stress cracks on CWS StoneCraft quartz seams and sink cutouts. Quartz doesn’t chip on its own. When a StoneCraft slab was set on an uneven cabinet run, or without proper support at the sink cutout, the stress concentrates at the seam and the cutout edges. We see this regularly in Morgan Hill kitchens where the floor settled or the original installer shimmed instead of leveling. We re-level the cabinet run, add support where needed, and repair or replace the affected slab section.
- Swollen and delaminating toe-kicks and back panels on CWS base units. Slab leaks, dishwasher overflow, and years of wet mopping against particleboard toe-kicks and back panels cause swelling and delamination. The box itself might still be solid. We replace the affected panels, seal them against future moisture, and inspect the adjacent boxes for early signs of the same damage.
- Rubbing drawer fronts and uneven reveals on CWS Signature Raised Panel runs. Raised-panel doors and drawers have tighter tolerances than slab fronts, and when hinge screws strip or the face frame shifts, the gaps go uneven and doors start catching. We re-square the face frames, replace stripped hinge plates, and reset the drawer fronts so the reveals run true across the whole run.
CWS Parts & Our Repair-vs-Replace Approach
When a CWS kitchen has a problem, the first question is whether the fix is a part, a refinish, or a replacement. We source OEM CWS hinges, glides, and touch-up finishes whenever they’re available, because OEM parts keep the original fit and don’t compromise whatever warranty coverage is still active on the cabinetry. For discontinued hardware or parts with long lead times, we use premium aftermarket soft-close mechanisms that match the existing box drilling, so the doors and drawers keep their alignment. We stock a range of common soft-close glides, hinge plates, and touch-up finishes locally for faster turnaround on CWS repair in San Martin and Morgan Hill service calls. If a CWS cabinet run has multiple failed boxes or a cracked quartz field, we price a targeted replace-or-refinish option against a full remodel and walk you through the numbers honestly. We don’t default to replacement when the existing boxes still have life in them. Call (833) 725-3508 and we’ll tell you what you’re actually looking at.
Our CWS Service Process – Step by Step
- 1
Diagnosis. We inspect the CWS boxes, face frames, drawer glides, hinges, and any quartz or granite surfaces, checking for the failure patterns we know this brand exhibits: glide dampener wear, MDF joint cracks, seam stress, and moisture-swollen panels. We also check the floor and cabinet leveling underneath, because a StoneCraft issue often starts below the counter.
- 2
Repair or install plan. We give you a written line-item scope with specific parts and materials named. If OEM CWS parts are available, we spec them. If they’re not, we show you the aftermarket option and explain the difference. No vague line items, no change orders you didn’t approve.
- 3
Execution. We pull permits when the project requires them, and we handle the structural, finish, and countertop work under one license. For cabinet repair, we remove and reset doors and drawer fronts, re-square face frames, and re-level bases before any quartz goes back down.
- 4
Testing. Every drawer cycles through its full travel, every door swings clean without rubbing, and we check seam integrity on quartz and granite with a straight edge and feeler gauge. We don’t call it done until it passes in front of us.
- 5
Warranty and follow-up. Our workmanship is warrantied, and we document the parts and finishes used so future service, whether by us or another contractor, has a clear record. If something shifts after install, we come back.
See the difference
Before
After
Before
After
Before
AfterCWS Products We Service & Install in Morgan Hill
We work on the CWS lines most common in Morgan Hill kitchens: ProSeries Shaker, EuroStyle Slab, Signature Raised Panel, and StoneCraft quartz surfaces. That covers full cabinet installation, door and drawer front replacement, face frame repair, finish matching and touch-up, drawer glide and hinge replacement, and quartz or granite countertop fabrication and installation. We stock common soft-close glides, hinge plates, and touch-up finishes for these lines locally, so most Morgan Hill service calls don’t wait on a parts shipment. Whether it’s a single failed drawer glide or a full StoneCraft island top that needs re-leveling and re-seaming, we handle it under the same roof.
We Also Service These Brands
Brookside Contractors isn’t tied to a single manufacturer’s catalog. Alongside CWS, we install and service KraftMaid and Wellborn cabinetry, Cambria, Silestone, and Caesarstone countertops, and Kohler and Toto fixtures. That breadth matters when a repair or upgrade touches more than one brand in the same kitchen, and it means we match the material to the project rather than forcing whatever one vendor supplies. Your project, your brands, one contractor.
FAQs – CWS Construction Service in Morgan Hill
Yes, in most cases. We order replacement CWS Shaker doors through available supply channels and match the existing finish using the original paint or stain code when it’s still legible, plus custom color matching for faded or discontinued finishes. The match won’t be invisible on a sun-faded run, but we can get it close enough that the difference only shows under direct light, and we’ll tell you upfront if a full reface of that cabinet face makes more sense. Call (833) 725-3508 and we’ll assess your doors.
Usually it’s the dampener piston inside the glide that has worn out, which is a part failure, not an adjustment issue. On CWS ProSeries boxes, the wide pot drawers are the first to go because they carry the most weight. Sometimes the drawer front is rubbing an adjacent door instead, which means the face frame shifted or the hinge plates stripped. We diagnose it in about ten minutes and replace the glides with OEM-matched soft-close units if the dampener is dead.
We recommend removing flooring under the cabinet footprint whenever the flooring is floating, because floating floors need room to expand and contract, and pinning them under cabinets causes buckling. For glue-down or nailed hardwood, tile, or sheet vinyl in stable condition, installing over the existing floor is usually fine. We’ll tell you which applies to your CWS repair in Gilroy or Morgan Hill kitchen during the estimate.
Yes, eventually. Quartz is rigid, and when the cabinet run underneath isn’t level, the slab spans the low spots and flexes under load, which concentrates stress at seams, sink cutouts, and overhangs. Morgan Hill homes on expansive soil are especially prone to cabinet runs going out of level over time. We re-level the cabinets before any StoneCraft top goes back down, which is the difference between a seam that holds and a crack that shows up two years later.
Yes, if the existing boxes are structurally sound. Refacing replaces the doors, drawer fronts, hinges, and applies a matching veneer to the face frames, which gives you a new kitchen look for about a third to half the cost of a full replacement. We’ll check the boxes for moisture damage and racking first, because refacing a failing box is throwing money at a problem that’ll come back. Call (833) 725-3508 for an assessment.
It depends on the scope, but here are the ranges we see across Morgan Hill:
| CWS Service | Typical Morgan Hill Price Range |
|---|---|
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Backsplash Installation | $800 – $2,500 |
| Kitchen Remodel | $14,000 – $45,000 |
| Small Kitchen Remodel | $9,000 – $20,000 |
Every job gets a written line-item quote before work starts, and the price doesn’t change unless you change the scope. Call (833) 725-3508 for an exact quote – estimates are free.
Book Your CWS Service in Morgan Hill, CA
If your CWS cabinets are sagging, your drawers are slamming, or your StoneCraft quartz is showing seam stress, call (833) 725-3508. We’ll diagnose what’s actually wrong, give you a straight answer on repair versus replace, and schedule the work when it fits your timeline.
Written by Nate Burrell, Owner at Brookside Contractors, serving Morgan Hill and South Santa Clara County.